Publiko produktet
QF Y Branch 16ga

QF Y Branch 16ga

Nordfab Quick-Fit® Y Branches (sometimes called “true wyes”) are standard with QF rolled ends, allowing quick connections with other QF ductwork. These Y shape branches are available with a 60° or 90º angle between the legs.

16 gauge steel material adds extra durability.

  • When ordering, specify galvanized steel material, 16 gauge (if nonstandard), dimensions A, B, C, end styles, and angle (60° and 90° available).
  • Both B & C each must be at least 50% of A, with B or C being at least 80% of the opposite leg.
  • Use the following formula to determine length: L = A + 4"
  • Available with flanged ends in diameters up to 72", and other various end types
  • Available with 60° and 90° angle
  • Other gauges available include standard 22 and 20, 18, 14, 12 and 10

Contact Nordfab or your local Nordfab dealer for assistance with branch configurations not shown below, larger sizes, and material / gauge options.

Quick-Fit has been used in a wide variety of applications, wherever dust collection or fine particulate transfer is required. Quick-Fit saves time and money on installation, is easy to clean out, is adaptable to existing ductwork, and is easily re-used during shop floor reconfigurations. Learn more about why Quick-Fit may be the best solution for you.

Özellikler
  • A. General Fabrication Requirements: Comply with SMACNA's "HVAC Duct Construction Standards - Metal and Flexible," Ch. 3, "Round, Oval, and Flexible Duct," based on indicated static-pressure class unless otherwise indicated.

    1. Construct ducts of galvanized sheet steel unless otherwise indicated. 304SS Optional.
    2. Basis-of-Design Product: Subject to compliance with requirements, provide Nordfab Ducting, LLC; Quick Fit (QF) Duct.

      B. Connection Joints: Joint types are fabricated in accordance with SMACNA's "HVAC Duct Construction Standards - Metal and Flexible," for static-pressure class, applicable sealing requirements, materials involved, duct-support intervals, and other provisions in SMACNA's "HVAC Duct Construction Standards - Metal and Flexible."

      1. Quick Fit Joints in Ducts 3 to 24 inches (76 to 510 mm) in diameter. Flange: Optional.
      2. Flanged Joints in All Ducts Greater than 24 inches (610 mm) in diameter.

      C. Longitudinal Seams: Seam types are fabricated in accordance with SMACNA's "HVAC Duct Construction Standards - Metal and Flexible," Figure 3-2, "Round Duct Longitudinal Seams," for static-pressure class, applicable sealing requirements, materials involved, duct-support intervals, and other provisions in SMACNA's "HVAC Duct Construction Standards - Metal and Flexible."

      1. Fabricated round ducts 3 to 24 inches (76 to 510 mm) in diameter to have laser-welded or plasma-welded longitudinal seams.
      2. Fabricated round ducts above 24 inches (610 mm) in diameter to have plasma-welded longitudinal seams.
    Teknik özellikler
    • Benzersiz ref.qf-y-branch-60-degrees
    • Ürün ailesiQuick-Fit Clamp Together Ducting
    • Ürün grubuBranches
    • TipObje (Tekil Nesne)
    • Yayınlanma tarihi2024-05-08
    • Baskı numarası1
    İlgili
    • Ana malzemeGalvanize Çelik
    • İkincil malzemeStainless steel 304
    • Tasarım yeriBirleşik Devletler
    • Üretim yeriBirleşik Devletler
    Sınıflandırma
    • BIMobject kategorisiHVAC - Dust Collection
    • IFC sınıflandırmasıDuct Fitting
    • ETIM KoduEG015540
    • ETIM AdıFittings, flanges and connectors
    • Uniclass 2015 koduPr_65_65_25
    • Uniclass 2015 açıklamasıDuctwork and fittings
    • CSI MasterFormat 2014 kodu23 31 13.19
    • CSI MasterFormat 2014 başlığıMetal Duct Fittings
    • OmniClass numarası23-33 49 00
    • OmniClass başlığıHVAC Ductwork

    Bölge bulunurluk durumu

    Kuzey Amerika
    Belize
    Bermuda
    Birleşik Devletler
    İngiliz Virjin Adaları
    Kanada
    Kostarika
    Meksika
    Panama
    Porto Riko
    Saint Martin