QF Tee Branch

Nordfab manufactures ducting for use in dust, mist, and fume collection systems.

Quick-Fit® Tee Branches are standard with QF rolled ends, allowing quick connections with other QF® ductwork.

When ordering, specify material; gauge (if nonstandard); dimensions A and C; and end styles if not all QF.
A1 to A2 must be the same dimension. C must be equal to or smaller than the A dimensions
Use the following formula to determine length: L = C + 8"
Available in galvanized steel and 304SS (as shown below) or optional 316SS or carbon steel
Available with flanged ends in diameters up to 72", and other various end types
Optional gauges 18, 16, 14, 12 and 10
QF Y Branches are a Nordfab Now^® product so items in the most commonly used sizes and material are in stock and can typically be shipped the day after order placement.

Contact Nordfab or your local Nordfab dealer for assistance with branch configurations not shown below, larger sizes, and material / gauge options.

Quick-Fit has been used in a wide variety of applications, wherever dust collection or fine particulate transfer is required. Quick-Fit saves time and money on installation, is easy to clean out, is adaptable to existing ductwork, and is easily re-used during shop floor reconfigurations. Learn more about why Quick-Fit may be the best solution for you.

Specifikim

A. General Fabrication Requirements: Comply with SMACNA's "HVAC Duct Construction Standards - Metal and Flexible," Ch. 3, "Round, Oval, and Flexible Duct," based on indicated static-pressure class unless otherwise indicated.
1. Construct ducts of galvanized sheet steel unless otherwise indicated. 304SS Optional.
2. Basis-of-Design Product: Subject to compliance with requirements, provide Nordfab Ducting, LLC; Quick Fit (QF) Duct.
B. Connection Joints: Joint types are fabricated in accordance with SMACNA's "HVAC Duct Construction Standards - Metal and Flexible," for static-pressure class, applicable sealing requirements, materials involved, duct-support intervals, and other provisions in SMACNA's "HVAC Duct Construction Standards - Metal and Flexible."
1. Quick Fit Joints in Ducts 3 to 24 inches (76 to 510 mm) in diameter. Flange: Optional.
2. Flanged Joints in All Ducts Greater than 24 inches (610 mm) in diameter.
C. Longitudinal Seams: Seam types are fabricated in accordance with SMACNA's "HVAC Duct Construction Standards - Metal and Flexible," Figure 3-2, "Round Duct Longitudinal Seams," for static-pressure class, applicable sealing requirements, materials involved, duct-support intervals, and other provisions in SMACNA's "HVAC Duct Construction Standards - Metal and Flexible."
1. Fabricated round ducts 3 to 24 inches (76 to 510 mm) in diameter to have laser-welded or plasma-welded longitudinal seams.
2. Fabricated round ducts above 24 inches (610 mm) in diameter to have plasma-welded longitudinal seams.

Specifikime teknike

Referencë unikeus-qf-tee-branch
Familja e produkteveQuick-Fit Clamp Together Ducting
Grupi i produkteveBranches
LlojiObjekt (një objekt të vetëm)
Data e botimit2024-05-08
Numri i botimit1

Lidhje

Product URLhttps://www.nordfab.com/en-us/products/qf-ducting/branches/us-qf-tee-branch
Përshkrimet teknikehttps://www.nordfab.com/-/media/files/nordfab/americas/americas-product-data-sheets/nordfab_tee_branch.pdf

Të ngjashme

Materiali kryesorGalvanized steel
Materiali dytësorStainless steel 304
Projektuar nëShtetet e Bashkuara
Prodhuar nëShtetet e Bashkuara

Klasifikimi

Kategoria BIMobjectNgrohes, ventilimit dhe ajrit të kondicionuar - Dust Collection
IFC classificationMontimi i tubave
Kodi ETIMEG015540
Emri ETIMFittings, flanges and connectors
Uniclass 2015 CodePr_65_65_25
Uniclass 2015 PërshkrimDuctwork and fittings
CSI MasterFormat 2014 Code23 31 13.19
CSI MasterFormat 2014 TitleMetal Duct Fittings
OmniClass Number23-33 49 00
OmniClass TitleHVAC Ductwork