Single Stage Infrared Heater, Model UX

Traduzido pelo Google,

O design do queimador fechado aprimora ainda mais todos os excelentes recursos do UA para aplicações de serviço pesado. Função pós-purga e garantia de tubo opcional de 10 anos.

UX apresenta uma construção de queimador totalmente fechada
40.000 a 220.000 BTU/h
Gás Natural e GLP
Configurações de "U" e "L", horizontal ou 45°
Compartimento de controles separados - eletrônica sem fluxo de ar, o queimador pode funcionar durante a manutenção
Módulo de ignição de autodiagnóstico
Refletores parabólicos de alumínio – mais eficientes na indústria
Ignição direta por faísca
Ventilado ou não ventilado
Queimador Jet Stream – melhor distribuição de calor, melhor combustão
Acoplamentos para serviço pesado – sem vazamentos, não podem ser apertados demais
Luz de status operacional
Controles de baixa tensão
Garantia de três anos em todos os componentes
Garantia de cinco anos no trocador de calor laminado a quente
Garantia de sete anos no trocador de calor aluminizado
Garantia de 10 anos no trocador de calor aluminizado com recurso de pós-purga

Especificação

Low-Intensity Single Stage Infrared Tube Heaters with minimum 65% radiant factor as determined by independent lab testing to EN416-2 Standard. Baffles required as per manufacturer’s instructions.
Assemblies shall be CSA approved low-intensity heater to the latest ANSI Z83.20 and CSA 2.34 for use in commercial and industrial applications. Burner shall be a positive pressure burner system, where exhaust gases and other products of combustion are not routed through the blower. The burner shall operate at a minimum gas inlet pressure of 5.0 inches W.C. (natural gas) or 11.5 inches W.C. (propane) and draw no more than 1 Amp at 120VAC, 60Hz.Burner head shall be chrome-plated steel and burner controls shall be located outside of the air supply stream to allow service and diagnostic control checks with the burner operating. Reflector shall be a 10-sided reflector design reflecting virtually 100% of the infrared energy out and away from the emitter tubes. Reflector shall be “Deep Dish” design with emitter tubes fully recessed within the reflector. Reflectors with less than 10 surfaces will not be allowed. Reflector shall be mill-finished aluminum, ASTM 1100, .024 inch thick aluminum sheet metal with two reflector support brackets for every 10 feet (3048 mm) reflector section. Reflectors shall extend below the lowest position of the tubing at all times. Reflector end caps shall be fitted to the end of each reflector run to reduce convective heat loss and shall be standard equipment. Emitter Tube shall be 4 inches (102 mm) diameter, minimum 16 gauge thickness. Combustion Tube shall be 4 inches (102 mm) diameter, 16 gauge, heat-treated type 1 aluminized steel tubing shall be required for all firing rates. Hot rolled steel combustion tubing shall not be allowed. Combustion tubing shall incorporate a welded, 11 gauge steel, 4 bolt flange to orient the burner to the tube as designed. Couplings shall be 16 gauge aluminized steel, minimum 12 inches in length, and be of heavy-duty design incorporating two 1-inch wide draw bands.
This product was specified based on best practice design to meet the specific engineered design criteria for this project.
Any submission for substitution must include the following material for consideration or bid will be deemed unqualified and rejected:
- Independent lab testing to EN416-2 standard dated no later than 6 months from date of submission showing a minimum 65% radiant factor
- Professional Engineer Stamped Design, calculations, and complete set of stamped drawings with alternate systems.
- Stamped fuel usage data showing a minimum 20% fuel savings over specified Superior Radiant Model
- Verification that Manufacturer successfully completed and passed the auditing requirements for ISO 9001 Quality Management System (QMS).

Especificação técnica

Ref. únicaux
Família de produtoSingle Stage Infrared Heaters
Grupo de produtosLow Intensity - Series U
TipoObjeto (objeto único)
Data de publicação2021-02-16
Número da edição1

Links

Url do produtohttps://www.superiorradiant.com/index.php/products/single-stage-infrared-tube-heaters/low-intensity/deluxe-high-efficiency-heater
Instruções de instalaçãohttp://bit.ly/2tnaXyv
Certificação do produtohttps://www.csagroup.org/testing-certification/product-listing/certificate/?cert=112168_0_000-2902-09
Descrição técnicahttp://bit.ly/2uhjBTA

Afins

Material principalAço
Material secundárioAlumínio
Desenhado emCanada
Fabricado emCanada

Classificação

Categoria BIMobjectAVAC - Aquecedores
Nome UNSPSCTubular heaters
Código UNSPSC40101822
Código Uniclass 2015Pr_70_60_36_72
Descrição Uniclass 2015Radiant tube heaters
CSI MasterFormat 2014 Code23 55 23
Título CSI MasterFormat 2014Gas-Fired Radiant Heaters
Número OmniClass23-33 15 17 13
Título OmniClassFuel Fired HVAC Radiant Heaters
CSI UniFormat II CodeD30
Título UniFormat II da CSIHVAC

Disponibilidade regional

América do Norte
Anguilla
Antigua and Barbuda
Aruba
Barbados
Belize
Bermuda
British Virgin Islands
Canada
Caribbean Netherlands
Cayman Islands
Collectivity of Saint Martin
Costa Rica
Cuba
Curaçao
Dominica
Dominican Republic
El Salvador
Greenland
Grenada
Guadeloupe
Guatemala
Haiti
Honduras
Jamaica
Martinique
Mexico
Montserrat
Nicaragua
Panama
Puerto Rico
Saint Kitts and Nevis
Saint Lucia
Saint Pierre and Miquelon
Saint Vincent and the Grenadines
Saint-Barthélemy
Sint Maarten
The Bahamas
Trinidad and Tobago
Turks and Caicos Islands
U.S. Virgin Islands
United States