Publish your products
Adaptive Modulating Infrared Heater, Model AM

Adaptive Modulating Infrared Heater, Model AM

SRP's modulating infrared tube heater that truly adapts to the environment, providing optimal thermal comfort. The Series AM combines the benefits of a fully modulating infrared heater with SRP’s 100% efficient reflector for maximum efficiency resulting in the best modulating heater on the market.

  • Fully modulates gas and air
  • Models rates 80,000 to 200,000 MBTU’s
  • Modulating differential 40%, largest in the industry
  • Fully automatic or manual control of burner modulation
  • Self-regulating, no fixed points – adapts to the demand regardless of conditions
  • Simple, effective controls
  • Easy troubleshooting – service while burner operating
  • Reliable – pressure measured mechanically
  • Outdoor approved
  • Separated controls compartment
  • Self-diagnostic potted ignition module
  • Parabolic aluminum reflectors
  • Nickel-chromed Jet Stream burner cup
Specification
  • Low-Intensity Adaptive Modulating Infrared Tube Heaters. Heavy-duty industrial/commercial infrared heater featuring the best overall performance in the industry automatically adjusts air and gas to properly regulate the temperature in a given space through a patent applied for technology to maintain up to 40% modulating differential by direct analog signal. The controls are to be simple, effective, and non-proprietary. The AM unit must read the room and adjust itself accordingly. Pre-programed units will not be accepted. Steady-state thermal efficiency will be in excess of 80%. 100% efficient reflector design. Baffles required as per manufacturer’s instructions. 

    Assemblies shall be CSA approved low-intensity heater to the latest ANSI Z83.20 and CSA 2.34 for use in commercial and industrial applications. Burner shall be a positive pressure burner system where exhaust gases and other products of combustion are not routed through the blower.   The burner shall operate at a minimum gas inlet pressure of 5.3 inches W.C. (natural gas) or 11.8 inches W.C. (propane) and draw no more than 1.2 Amp at 120VAC, 60Hz.

    Burner head shall be chrome-plated steel and burner controls shall be located outside of the air supply stream to allow service and diagnostic control checks with the burner operating. Reflector shall have a minimum 10-sided design reflecting virtually 100% of the infrared energy out and away from the emitter tubes. Reflector shall be “Deep Dish” design with emitter tubes fully recessed within the reflector. Reflectors with fewer than 10 surfaces will not be allowed as they allow energy to bounce back to the main heat exchanger tubing. Reflector shall be mill-finished aluminum, ASTM 1100, .024 inch thick aluminum sheet metal with two reflector support brackets for every 10 feet (3048 mm) reflector section. Reflectors shall extend below the lowest position of the tubing at all times. Reflector end caps shall be fitted to the end of each reflector run to reduce convective heat loss and shall be standard equipment. Emitter Tube shall be 4 inches (102 mm) diameter, minimum 16 gauge thickness. Combustion Tube shall be 4 inches (102 mm) diameter, 16 gauge, heat-treated type 1 aluminized steel tubing and shall be required for all firing rates.  Hot rolled steel combustion tubing shall not be allowed. Combustion tubing shall incorporate a welded, 11 gauge steel, 4 bolt flange to orient the burner to the tube as designed. Couplings shall be 16 gauge aluminized steel, minimum 12 inches in length, and be of heavy-duty design incorporating two 1-inch wide draw bands.

    This product was specified based on best practice design to meet the specific engineered design criteria for this project.  Any submission for substitution must include the following material for consideration or bid will be deemed unqualified and rejected:

    • Independent testing to show adaptive modulation to 40% modulating differential 
    • Professional Engineer Stamped Design, calculations, and complete set of stamped drawings with an alternate system.
    • Stamped fuel usage data showing a minimum 20% fuel savings over specified Superior Radiant Model 
    • Verification that Manufacturer successfully completed and passed the auditing requirements for ISO 9001 Quality Management System (QMS).
Technical specification
  • Unique ref.am
  • Product familyMODULUS® Modulating Heater
  • Product groupSeries AM
  • TypeObject (single object)
  • Date of publishing2021-02-16
  • Edition number1
Related
  • Material mainSteel
  • Material secondaryAluminium
  • Designed inCanada
  • Manufactured inCanada
Classification
  • BIMobject CategoryHVAC - Heaters
  • UNSPSC nameTubular heaters
  • UNSPSC code40101822
  • Uniclass 2015 CodePr_70_60_36_72
  • Uniclass 2015 DescriptionRadiant tube heaters
  • CSI MasterFormat 2014 Code23 55 23
  • CSI MasterFormat 2014 TitleGas-Fired Radiant Heaters
  • OmniClass Number23-33 15 17 13
  • OmniClass TitleFuel Fired HVAC Radiant Heaters
  • CSI UniFormat II CodeD30
  • CSI UniFormat II TitleHVAC

Region availability

North America
Anguilla
Antigua and Barbuda
Aruba
Barbados
Belize
Bermuda
British Virgin Islands
Canada
Caribbean Netherlands
Cayman Islands
Collectivity of Saint Martin
Costa Rica
Cuba
Curaçao
Dominica
Dominican Republic
El Salvador
Greenland
Grenada
Guadeloupe
Guatemala
Haiti
Honduras
Jamaica
Martinique
Mexico
Montserrat
Nicaragua
Panama
Puerto Rico
Saint Kitts and Nevis
Saint Lucia
Saint Pierre and Miquelon
Saint Vincent and the Grenadines
Saint-Barthélemy
Sint Maarten
The Bahamas
Trinidad and Tobago
Turks and Caicos Islands
U.S. Virgin Islands
United States